Supplies Needed
1 tube of choice – I
used the adorable artwork of Eos Sparks which can be purchased from Digital Art Heaven.
Vix Mask 451 here
Plug Ins used:
Mura’s Meister - Copies
“Autumn Day” is a FTU tagger size scrap kit created
by ZaZa of Scrap and Tubes and can be downloaded from her blog here. The post is dated Sept. 6, 2016.
This tutorial was
written assuming you have working knowledge of PSP.
~♥~ Let’s get started ~♥~
Open up a 700 x 700 blank canvas.
Flood fill white.
Copy and paste El 32 as a new layer.
Resize 40%
Duplicate/Resize 60%/Free Rotate
Right 7 degrees
In your layers pallet move it below
the large frame and move into position at the right side of the large frame –
see my tag for reference.
Duplicate/Mirror
To each of the 3 frames:
Click inside of it with your Magic
Wand.
Selections/Modify/Expand by 2.
New Raster layer below the frame.
Copy and paste Paper 2 Into
Selection.
Deselect.
Copy and paste your tube as a new
layer over the paper that belongs to the small Left frame.
Move it into a position you like.
Change the Properties of the tube to
Soft Light.
Duplicate/Mirror
The tube should have appeared in the
small right frame – be sure this tube is below the right frame in your layers
pallet.
To each of these tubes:
Highlight the paper that’s just
below the tube.
Click outside of the paper.
Highlight the tube.
Tap the delete key.
Deselect.
Duplicate the tube (if you can’t see
it very well).
Copy and paste Element 37 as a new
layer.
Resize 30%
Use your Target Tool and change to a
color that matches your tube. I used #509443.
Duplicate the element.
Resize 80%
Free Rotate Right 7 degrees.
Move into position at the top of the
right frame.
Duplicate/Mirror.
Copy and paste your tube as a new
layer.
Position it in front of the large
frame.
Open up Element 24.
Use your Selection Tool set on Rectangle
and section out the lone acorn on the left.
Copy and paste it as a new layer on
your working canvas.
Resize 40%
Apply Mura’s Meister – Copies:
Use these settings –
Position this ring just above your
white canvas and behind the large frame.
Duplicate/Resize 80%
Move into position behind the right
frame.
Duplicate/Mirror
Copy and paste Element 16 as a new
layer.
Resize 20%
Apply Mura’s Mesiter – Copies:
Use same settings.
Move into position behind the large
acorn wreath you just made.
Once it’s in exact position to where
the flowers peek out from the outside of the acorn wreath, highlight the acorn
wreath and click inside of it with your Magic Wand.
Selections/Modify/Expand by 5.
Highlight the flower wreath.
Tap the delete key.
Deselect.
Duplicate the flower wreath.
Resize 80%
Move into position behind the right
acorn wreath.
Duplicate
Move into position behind the left
acorn wreath.
Copy and paste Element 17 as a new
layer.
Resize 80%
Duplicate 2x’s and move all 3
elements into position – see my tag for reference.
Highlight your white background.
New Raster layer.
Select All.
Copy and paste Paper 7 Into
Selection.
Deselect.
Apply the mask.
Merge Group.
New Layer (above the merged mask
layer).
Select All.
Copy and paste Paper 1 Into
Selection.
Deselect.
Apply the mask.
Merge Group.
Change the Properties to Multiply.
Add your name:
Color Pallet:
Foreground: #884204
Background: #dc3638
Make your Text Tool active
Set the Stroke Width to 2.
Type your name
Give it a slight Inner Bevel:
Make your Freehand Selection Tool
active.
Encircle the bottom half of your
name – make the line a little wavy:
Selections/Modify/Inside Outside
Feather:
Both checked
Feather amount: 20
OK
Adjust/Hue and Saturation/Colorize:
Hue 93
Saturation: 140
OK
The bottom half of your name should
have turned green.
Adjust/Add Remove Noise/Add Noise:
Gaussian and Monochrome checked
Noise: 50%
OK
Deselect.
Add your copyright.
Close out your white background.
Merge Visible.
Resize all layers to a size of your
choice.
Save.
I’d love to see your results.
Hugs,
Bev
