Supplies Needed
1 tube of choice – I used the beautiful artwork of Katerina Koukiotis which can
be purchased from Digital Art Heaven.
Font of choice – I used Agenda King here
Vix mask 451 here
My template 192 here
Plug Ins used: Greg's Factory Output Vol. II - Pool Shadow
“Dance of Autumn” is a Tagger Size scrap kit created by me, Bev of HorsePlay’s Pasture Designs and can be purchased from Digital Art Heaven here.
This tutorial was written assuming you have a working knowledge of PSP.
~♥~ Let’s
get started ~♥~
Open the template.
Shift + D.
Close out the original.
Delete the credit layer.
Highlight Layer 1.
Click on it with your Magic Wand.
New Raster layer.
Copy and paste Paper 13 Into Selection.
Deselect.
Delete the template layer.
Give the paper a slight Inner Bevel:
Highlight Layer 2.
Click on it with your Magic Wand.
New Raster layer.
Open Paper 4.
Mirror and Copy (close the paper out).
Make your working canvas active.
Paste the Paper Into Selection.
Deselect.
Delete the template layer.
Give the paper the same slight Inner Bevel.
Highlight Layer 3.
Select All/Float/Defloat.
New Raster layer.
Copy and paste Paper 10 Into Selection.
Apply Greg’s Factory Output Vol. II – Pool
Shadow.
Use Default Settings:
Adjust/Add Remove Noise/Add Noise:
Uniform and Monochrome checked
Noise: 30%
OK
Deselect.
Delete the template layer.
Repeat the above step with Layers 4 and 11 but DO NOT DELETE TEMPLATE LAYER 11!!
Highlight Layer 5.
Click on it with your Magic Wand.
New Raster layer.
Open up Paper 4 and Mirror it and then Flip
it.
Copy.
Make your working canvas active and paste Into
Selection.
Close the paper layer out.
Deselect.
Delete the template layer.
Give the paper the same slight Inner Bevel.
Highlight Layer 6.
Select All/Float/Defloat.
New Raster layer.
Copy and paste Paper 4 Into Selection.
Apply the same Noise effect.
Deselect.
Delete the template layer.
Highlight Layer 7.
Repeat the above step.
Highlight Layer 8.
Click on it with your Magic Wand.
New Raster layer.
Copy and paste Paper 5 Into Selection.
Copy and paste your tube as a new layer above
the paper layer. Resize as you
like. If you’re using the same tube as I
did, Resize 50%.
Move into a position you like.
Right click on it in your layers pallet and
choose “Promote Section to Layer” from the sub menu.
Change the Properties of the promoted tube
layer to Burn.
Deselect.
Repeat the above step with Layer 9.
Delete the original tube layer.
Highlight Layer 10.
Click on it with your Magic Wand.
New Raster layer.
Copy and paste Paper 4 Into Selection.
Copy and paste your tube as a new layer above
the paper layer. If you’re using the
same tube as I did, Resize 44%. See my tag for placement and
also be sure to keep your tube above the paper that belongs to template Layer
11.
In this part of the tutorial I will show you
how to make it look like the hand is outside of the frame.
Move your tube into position (above the paper
layer that belongs to template Layer 11) by positioning it so that the right
side of the tube aligns with the right side, top, and bottom of the paper that
belongs to template Layer 10. Be sure
that the tube even covers the right corners of the paper.
Once you have the tube in exact position make
your Freehand Selection Tool active set on Point to Point with a Feather of 1.
Zoom in and section out the lower left corner
of the tube from just below the hand (the red area on my example):
Once you have that sectioned off, tap the
delete key.
Deselect.
Highlight template Layer 10.
Click anywhere outside of it with your Magic
Wand.
Highlight the tube layer.
Make your Eraser Tool active and erase any
areas outside of the paper you don’t want.
Deselect.
Highlight template Layer.
Click anywhere outside of it with your Magic
Wand.
Highlight the Paper layer that belongs to
template Layer 11.
Erase the area of that thing little frame that
overlaps the hand.
Deselect.
You can now delete Template Layer 11.
Add your elements. I used:
El 44:
Resize 40%/Free rotate Left 90 Degrees
El 10:
Resize 45%
El 28:
Resize 55%/Duplicate
El 28:
Resize 45%/Duplicate 3 times for a total of 4
El 16:
Resize 60%/Mirror
El 12:
Resize 40%/Duplicate/Mirror
Paste El 12 again: Resize 40% and place behind flowers at upper
right circle. Duplicate leaf
element/Flip/Mirror and place behind flowers at lower left circle.
El 27:
Resize 45%/Duplicate/Mirror/Flip
El 28:
Resize 45%/Duplicate/Flip/Duplicate both leaf layers/Mirror
El 18:
Resize 40%
El 35:
Resize 60%
Highlight your white background.
New Raster layer.
Select All.
Copy and paste Paper 11 Into Selection.
Deselect.
Apply the mask.
Merge Group.
Duplicate/Resize 70%/Duplcate/move both
resized mask layers into position behind each of the circles at the top right
and bottom left.
Add your copyrights.
Add your name.
Color Pallet:
Foreground: Null
Background: #282111
Type your name.
Convert
to Raster Layer.
Give it the same slight Inner Bevel.
I hope you enjoyed this tutorial.
I’d love to see your results.
Email me!
Hugs,
Bev
